Archive for June 2019

Back to Archive Index

DIY (24)

Garden (1)

Garden Tools & Supplies (1)

  • How To Sharpen A Chain Saw

    A chain saw needs to be sharpened often or it won't do its job properly. To sharpen the cutters, which are the concave -shaped teeth that do the work, you need a round file and a guide to help you keep the file aligned at the proper angle. You can also use of of several tools to sharpen the chain.

    Read More

Home Improvement (2)

Home Improvement (1)

Kitchens (7)

  • How To Remove A Farmhouse Sink

    The procedure for removing a farmhouse sink is similar to that for removing other types of sinks. A big difference is that you'll be left with a hole in the countertop and one in the front of the cabinet. If the replacement sink isn't the same size as the original, you'll need cabinet modifications

    Read More
  • How To Position Faucets With Undermount Sinks

    The faucet for an undermount sink must be mounted on the countertop. It usually gets centered behind the sink about 2 to 4 inches from the edge, but it can go anywhere, provided there's enough room for it. Faucets that require more than one hole should line up with one side of the sink or a tangent.

    Read More
  • Installing A Stainless Steel Sink

    Stainless steel sinks are lightweight and among the easiest of sinks to install, especially drop-in ones. After cutting the hole, you caulk around the edges of the opening, drop in the sink and secure it with mounting brackets. Make the drain and faucet connections, check for leaks and you're done.

    Read More
  • Cast Iron Sinks Vs. Stainless Steel Sinks

    Cast iron sinks are heavier than stainless steel ones, and they are coated with porcelain enamel that can chip. Both types of sinks can be stained and both require roughly the same type of care. If you're budget conscious, choose stainless steel. It costs several hundred dollars less on average.

    Read More
  • How To Install A Kitchen Sink

    Virtually all kitchen sinks sit on a countertop, so cutting a hole for the sink is an essential part of the job of installing one. Installing the faucet and drain are also important procedures. Most sinks come with clips or connectors and instructions for using them. Read the instructions carefully.

    Read More
  • Composite Sinks Vs. Stainless Steel

    Both composite granite and stainless steel sinks offer durability that could last for years, with proper care. Composite sinks tend to cost a little more than their stainless counterparts. In some cases, composite sinks can also warp or melt in places due to hot items placed in them.

    Read More
  • Drop-In Sink Not Sitting Flat

    If you're installing a drop-in sink, and it doesn't sit flat, the hole in the countertop might be too small or the wrong shape. The problem could also be that caulk from the old sink was left on the countertop. If the sink is flat but not level, the entire countertop or cabinet is out of level.

    Read More

Landscaping (4)

  • How To Prune Rosemary

    Pruning rosemary is a bit like pruning evergreen shrubs, since this plant is indeed a perennial evergreen. Trim lanky sprigs throughout the growing season to help it retain its shape. Cut small sprigs for culinary use and for drying at any time as well. Don't cut old growth, as it won't regrow.

    Read More
  • How And When To Prune Garden Geraniums

    Geraniums don't require much pruning since they're usually annuals when grown in garden beds. Even so, deadhead the plants weekly to keep fresh blooms coming. Prune leggy or damaged stems whenever necessary to help the plant keep its shape and its good health. Discard removed stems and blooms.

    Read More
  • Pruning Shrubs: What You Should Know

    When pruning shrubs to generate more flowers or foliage, you generally using heading cuts, and the best time to do this is early to late spring, depending on the species. You can use thinning cuts to remove dead and diseased branches an control growth any time, but late winter is the best.

    Read More
  • How And When To Prune Lilacs

    Pruning lilacs is best done within a few weeks after the blooms fade. Trim them with bypass pruning shears, cutting blooms off just above the place the stem forks beneath the bloom. Old growth should also be cut back every few years to help keep the bush productive. Remove diseased or dead branches.

    Read More

Lawn (1)

  • How To Build Cornhole Game Boards

    Building your own cornhole game boards can be a simple woodworking project suitable for beginners. The boards use basic lumber and plywood and can be built to American Cornhole Organization official dimensions.

    Read More

News (44)

Real Estate (23)

Remodel (3)

  • What Is A Dry Bar Sink?

    A dry bar sink is basically just a bar sink that has been installed without a faucet. It may or may not have a drain, and if it does, the drain may not be connected to plumbing but may empty into a bucket or on the ground. Bar sinks are usually small and decorative, and may be undermount or drop-in.

    Read More
  • How To Solder Copper Plumbing Pipes

    The key to a good solder job is proper preparation of the pipe and fitting. Be sure to maintain the heat on the connection long enough to get good wicking action.

    Read More
  • How To Cut Sheet Metal

    Cutting most sheet metal materials requires nothing more than a pair of tin snips, but there are some tricks to making straight and smooth cuts. There are also some specialty versions of snips that are helpful for specific cuts.

    Read More

Windows, Doors & Walls (1)

  • How To Build A Living Fence

    Learn what is meant by the term "living fence" and get some ideas on how you can apply this green building concept to your yard. Include how-to instructions for creating a living fence from willow rods.

    Read More