How to Get Rid of Inchworms on Trees

Inchworms, also known as cankerworms, attack trees by feeding on their foliage. These harmful pests consume the tissue between leaves' veins, leaving behind skeletal frameworks. Their feeding ruins trees' aesthetic appearance and stops the plants from photosynthesizing, or producing food. If left untreated over time, infested trees die. With the help of multiple treatment options, each targeting a specific developmental phase of inchworms, you can eradicate inchworms from your landscape.

23640279
credit: Hemera Technologies/PhotoObjects.net/Getty Images
Male inchworms sport wings while the females remain wingless.

Tree Banding

Step 1

Measure the distance around an affected tree's trunk 2 to 3 feet above ground level in fall to mid-winter. That time of year is before adult inchworms emerge from soil. Cut out a piece of cotton batting or insulation equal in length to the trunk's measurement and 6 to 12 inches wide.

Step 2

Wrap the piece of cotton batting or insulation around the tree's trunk 2 to 3 feet above ground level. Tape the material's ends together with electrical tape, securing the material in a ring around the trunk.

Step 3

Cut a piece of tar paper to make it equal in width to and 4 to 5 inches longer than the piece of cotton batting or insulation wrapped around the tree trunk. Wrap the tar paper around the tree trunk, placing it on top of the batting or insulation. Overlap the tar paper's ends. Staple along the edge of the tar paper's exposed end with a stapler containing 1/4-inch-long staples, securing the tar paper in a ring around the tree trunk. Staple around the top edge of the tar paper to attach it to the cotton batting or insulation and keep it from slipping downward.

Step 4

Put on a pair of disposable rubber gloves. Scoop some sticky adhesive with your gloved fingers. Rub the adhesive on the surface of the tar paper. Apply additional adhesive as needed to create a 3-inch-wide sticky adhesive ring around the entire piece of tar paper. Remove your gloves, and throw them away.

Step 5

Wait for the tar paper's sticky adhesive to become full with adult inchworms. Put on a pair of disposable gloves. Cut or tear the tar paper off the cotton batting or insulation. Fold the tar paper in half, and tuck it into a plastic zipper bag. Seal the bag, and discard it in a trash bin.

Step 6

Attach a new piece of tar paper over the tree trunk's cotton batting or insulation in the same manner you attached the first piece of tar paper. Apply a new ring of sticky adhesive to the tar paper, repeating the procedure you used previously.

Step 7

Replace the tree trunk's tar paper as needed to trap as many adult inchworms as possible in the sticky adhesive. Remove both the tar paper and cotton batting or insulation when adult inchworms stop emerging from the soil.

Dormant Horticultural Oil

Step 1

Wait until late fall or early winter, when adult inchworms finish emerging from soil and die but before their eggs hatch in spring. Pour 5 tablespoons of dormant horticultural oil and 1 gallon of water in a tank sprayer to create a 2 percent solution of the oil spray. Stir the liquid thoroughly with a disposable stick.

Step 2

Screw the lid on the tank sprayer, tightening it completely. Move the tank sprayer's pressurizing handle up and down until it becomes difficult to do so. That task pressurizes the tank.

Step 3

Point the tank sprayer wand's nozzle at an affected tree's trunk. Press the nozzle's button to activate the spray. Move the wand up and down slowly while walking around the tree. Keep the nozzle pointed at the tree's trunk. Shake the tank sprayer up and down every 5 minutes to prevent the oil from separating from the water. Coat the entire trunk completely with the spray, ensuring that the spray comes into direct contact with all inchworm eggs.

Bacillus Thuringiensis Spray

Step 1

Wait until all inchworm eggs hatch and the hatched larvae are less than 1 inch in length. Pour 4 teaspoons of Bacillus thuringiensis and 1 gallon of water into a tank sprayer. Mix the solution thoroughly with a disposable stick.

Step 2

Tighten the tank sprayer's lid to secure the solution inside the tank. Pump the sprayer's pressurizing handle up and down until it becomes difficult to do so. That action pressurizes the tank.

Step 3

Point the tank sprayer wand's nozzle at an affected tree's leaves. Press the nozzle's button to activate the spray. Spray the solution on the top and bottom sides of the leaves, covering all feeding inchworms with the spray. Coat each leaf surface completely with the liquid, stopping the spray just before it begins to drip from the leaves. Shake the sprayer tank every 5 minutes to keep the solution's contents from separating. Use a ladder if needed to reach the top of the tree's foliage.

Step 4

Reapply the Bacillus thurnigiensis-water solution every seven days as needed until you no longer see inchworms. Coat the entire canopy during each application.