Save money and conserve precious rain water by constructing your own rain barrel, which you can use to water your plants and lawn. About 600 gallons of water can be collected from 1 inch of rain falling off a 1,000 square foot house. Decorative elements like wooden stakes can be used to make the barrel a standout feature rather than an eyesore in your yard.

rain barrel decorated with wooden stakes and flowers
credit: Matthew Ashman
Rain barrel supplies.
credit: Matthew Ashman

Step 1 Make a Drain Hole

Drill a hole in the barrel using the 1-inch drill bit about 5 inches up from the base. If there is a curve in the barrel, be sure to drill just above the curve. Remove any excess plastic.

drilling a hole into the plastic barrel
credit: Matthew Ashman

Step 2 Install the Drain

Apply some silicone sealant to the threading of the boiler drain and screw it into the hole you just drilled. You may need to use a little bit of force to make sure the threading catches on the barrel.

Attaching the drain.
credit: Matthew Ashman

Step 3 Create an Overflow Hole

It's up to you where to place your overflow hole, but it is preferable to install it somewhere hidden in the back of the barrel. Wherever it ends up, be sure to place it about 3 inches from the top of the barrel. Use the 1-inch drill bit to create this hole, too. Then coat the threading on the hex nipple with silicone sealant and screw it into the hole. You could either just cap the overflow hole to prevent any bugs or debris from entering, or during a storm, you could also attach a hose to it and place the hose in a more desirable location.

attaching a pipe to the overflow hole
credit: Matthew Ashman

Step 4 Attach the Adapters

Coat the threading on the boiler drain on the inside of the barrel with more silicone sealant. Now attach one of the adapters, while having a helper hold the boiler drain from the outside of the barrel with a wrench. Do the same thing with the overflow hole as well.

Attaching the adapters inside the barrel.
credit: Matthew Ashman

Step 5 Create Filter Holes

If the screw-top lid on your barrel came with pour spouts (which this barrel did), then you can skip this step, as the pour spouts will act as filter holes. To create filter holes on top of the barrel, draw three 3-inch holes on the lid of your barrel, preferably in the center. Now cut those holes out using the hole saw.

Pour spouts act as filter holes.
credit: Matthew Ashman

Step 6 Cover the Filter Holes

Cut out two screen pieces large enough to cover the filter holes on the underside of the barrel lid. Apply a liberal amount of the silicone sealant around the underside of the lid around the holes and place the screens over the holes. Repeat this step on the top side of the lid.

Applying the silicone for the screen.
credit: Matthew Ashman

Step 7 Install the Rain Barrel

Situate the retaining wall blocks in an area that is underneath a rain gutter and place the rain barrel on top. Having the rain barrel on top of blocks makes it easier to get water out of the spout. Make sure all of blocks are level before placing the barrel on them. This will help to distribute the weight evenly since the barrel can weigh up to 450 pounds when full of water. You now have a fully functional rain barrel, but there are a few more steps to make it less of an eyesore around the yard.

Placing the rain barrel in the right spot.
credit: Matthew Ashman

Step 8 Cut Drain & Overflow Holes on the Stakes

Line one of the wooden stakes up with the boiler drain and mark the area on the wooden stake. This is where you will cut a hole using the 3-inch hole saw. Be careful, as there isn't a lot of room for error when cutting out the hole. Now do the same with another wooden stake but this time for the overflow hole.

Using a hole saw to create holes for boiler drain.
credit: Matthew Ashman

Step 9 Paint the Stakes

Paint all of the wooden stakes with the exterior paint/primer combo.

Using exterior paint and primer for stakes.
credit: Matthew Ashman

Step 10 Install Stakes Around the Barrel

Once all of the paint is dry, it's time to wrap the stakes around the barrel. You might need a helper for this. Start with the stake meant to go over the boiler drain, carefully fitting the drain through the hole. Make sure the bottom of the stake is aligned with the bottom of the barrel. Continue with the remaining stakes, making sure to fit the pre-drilled stake over the overflow spout as well. Once the stakes are all in place, wrap two sets of bungee cords around them to keep them together. Place the bungee cords where you want your decorative twine to go.

Setting up the stakes around the barrel.
credit: Matthew Ashman

Step 11 Wrap the Stakes With Twine

Wrap twine around each bungee cord to hide them. Start by tying a knot around the bungee cord and start wrapping the twine around the cord until it's completely hidden. Secure the end with a tight knot and cut off excess twine. Keeping the bungee cord underneath the twine will help keep the wooden stakes securely in place.

wrapping twine around the bungee cords
credit: Matthew Ashman

Step 12 Install the Flex-a-Spout

Attach the flex-a-spout to your rain gutter according to the manufacturer's instructions. Hover the other end of the spout over the filter holes. It does not need to be attached to the barrel itself.

attaching the flex-a-spout to the rain gutter
credit: Matthew Ashman

Using the Rain Barrel

To use the fresh and nutrient-rich water in your rain barrel after it has rained, you can attach a hose to the boiler drain and use it to water your yard, or fill up a watering can to water plants. The filters should keep any mosquitoes out of the barrel and also keep most debris out as well. Be sure to remove any leaves that may block the filter holes. For colder areas, you may want to leave the boiler drain open to avoid any ice damage.

finished rain barrel installed outside
credit: Matthew Ashman